服务热线电话

400-6188-756

使用超声波清洗机清洗电路板需要注意什么?

来源:/ 时间: 2022-04-12 浏览次数: 2

1.半水清除和主水清理制作工艺应取用溶剂和双蒸水,加上一定量的表活剂和洗涤剂食品防腐剂。这类清洗处于溶剂清洗和水清洗中间。洗洁剂剂属于溶剂、易燃性性有机化学溶剂、高开口闪点、微毒、安全系数运用,但干燥后务必清洗水。
1. semi water cleaning and main water cleaning processes shall use solvent and double distilled water, plus a certain amount of surfactant, detergent and food preservative. This kind of cleaning is between solvent cleaning and water cleaning. Detergent belongs to solvent, flammable organic chemical solvent, high opening flash point, slight toxicity and safety factor, but the water must be cleaned after drying.
2、通过式喷淋清洗烘干线清水技术性清水技术是清水技术性的发展标底目地,务必创立清水和排水管道处理生产车间。
2. Clean water technology of through spray cleaning and drying line is the benchmark of the development of clean water technology. It is necessary to establish a production workshop for the treatment of clean water and drainage pipes.
全自动超声波清洗机
3.在电焊焊接整个过程中运用无清除或无清理的焊锡膏,助焊膏马上焊入下一个制作工艺清除,目前已不运用永久免费清除专业性作为替代专业性,十分是移动通信技术产品绝大多数是一次性的替代品。
3. In the whole process of electric welding, the solder paste without removal or cleaning is used, and the solder paste is immediately welded into the next manufacturing process for removal. At present, the permanent free removal specialty is no longer used as a substitute specialty, and most mobile communication technology products are disposable substitutes.
4、行业专用超声波清洗机主要是实际操作溶剂的融解才可以除去污染物质。采用溶剂清洗,因为蒸发快,融解才可以强,因此机器设备规定朴素。
4. The special ultrasonic cleaning machine for the industry is mainly the actual operation of solvent melting to remove pollutants. Solvent cleaning is adopted, because the evaporation is fast and the melting can be strong, so the machinery and equipment regulations are simple.
(1)必须清洗超音波清洗槽中的线路板。随后干预清水或溶剂清洗盘泡浸必须清洗的住所Z好是置放。
(1) The circuit board in the ultrasonic cleaning tank must be cleaned. Then intervene with clean water or solvent to wash the dish, soak the place that must be cleaned, and place it well.
(2)接入通过式喷淋烘干清洗线细致开关电源的电源,开启电源总开关,运行超音波电源开关,设定工作时间,机械设备控制通常可调式020分鐘或开与关。数据控制可立即设置工作时间。
(2) Connect the power supply of the fine switching power supply of the through spray drying and cleaning line, turn on the main power switch, run the ultrasonic power switch, set the working time, and the control of mechanical equipment is usually adjustable for 020 minutes or on and off. Data control can set working hours immediately.
(3)设定好工作时间后,清洗机希望1至5min后Z开始工作中,清洗机将积极完毕工作中,假如您开启清洗机作用一切正常开启或工作时间太长,立即带清洗电脑主板就可以。
(3) After setting the working time, the cleaning machine hopes that Z will start working in 1 to 5 minutes, and the cleaning machine will actively complete its work. If you turn on the cleaning machine, everything will start normally or the working time is too long, you can immediately bring the cleaning computer motherboard.
通过以上的内容我们应该对于超声波清洗设备内容有了一定的了解,更多的精彩内容请继续关注我们的网站及相关资讯/
Through the above content, we should be for ultrasonic cleaning equipment With a certain understanding of the content, please continue to pay attention to our website and related information for more wonderful content/

联系我们

詹老师:18663767799(微信同号)

陶老师:13011716033(微信同号)

张老师:18663767790(微信同号)

:1476171179/1500705758

:jnkergs@163.com

:地址:济南市先行区太平街道机械装备产业园创业路二号

关注爱游戏官网

  • 扫一扫了解更多

  • 扫一扫了解更多

备案号:鲁ICP备18049717号-1 技术支持:网站建设·推广运营